Rice-lake 880 Performance Series Indicator/Controller Techni Bedienungsanleitung Seite 71
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
EDP Commands 65
6.0 EDP Commands
The 880 indicator can be controlled by a personal computer or terminal connected to the EDP commands which
can simulate front panel key press functions, display and change setup parameters, and perform reporting
functions.
6.1 The EDP Command Set
The EDP command set can be divided into seven groups: key press commands, reporting commands, the
RESETCONFIGURATION special function command, parameter setting commands, normal mode commands, error
conditions and batching control commands.
When the indicator processes an EDP command, it responds
with the message OK. The OK response verifies that
the command was received and has been executed. If the command is unrecognized or cannot be executed, the
indicator responds with
??.
The following sections list the c
ommands and command syntax used for each of these groups.
6.1.1 Key Press Commands
Key press EDP commands (see Table 6-1) simulate pressing the keys on the front panel of the indicator. These
commands can be used in both setup and weighing mode. Several of the co
mmands serve as “pseudo” keys,
providing functions that are not represented by a key on the front panel.
For example, to enter a 15-pound tare weigh
t using EDP commands:
1. Type K1 and press
ENTER (or RETURN).
2. Type K5 and press
ENTER.
3. Type KTARE and press
ENTER.
Command Function
KMENU Press the MENU key
KZERO Press the ZERO key
KUNITS Press the UNITS key
KPRINT Press the PRINT key
KTARE Press the TARE key
KGROSSNET Press the GROSS/NET key
KGROSS Go to gross mode (pseudo key)
KNET Go to net mode (pseudo key)
KDISPACCUM Display ACCUM (pseudo key)
KDISPTARE Display tare (pseudo key)
KCLR Press the CLEAR key (pseudo key)
KCLRCN Reset consecutive number (pseudo key)
KCLRTAR Clear tare from system (pseudo key)
KLEFT In menu mode, move left in the menu
KRIGHT In menu mode, move right in the menu
KUP In menu mode, move up in the menu
KDOWN In menu mode, move down in the menu
KSAVE In menu mode, saves the current
configuration (pseudo key)
KEXIT In menu mode, saves the current
configuration then exits to weigh mode
(pseudo key)
K0–K9 Press number 0 (zero) through 9 (pseudo
keys)
KDOT Press the decimal point (.) (pseudo key)
KENTER Press the ENTER key (pseudo key)
KLOCK Lock specified front panel key. For
example, to lock the ZERO key, enter
KLOCK=KZERO. (pseudo key)
KUNLOCK Unlock specified front panel key. For
example, to unlock the PRINT key, enter
KUNLOCK=KPRINT. (pseudo key)
KDATE Display date (pseudo key)
KTIME Display time (pseudo key)
KESCAPE Exits the selected parameter. Returns to
weigh mode if a parameter is not selected
(functions identical to the MENU key in
menu mode) (pseudo key)
KPRIM Change to primary units (pseudo key)
KSEC Change to secondary units (pseudo key)
Command Function
Table 6-1. EDP Key Press Commands
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Verwandte Produkte und Handbücher für Waage Rice-lake 880 Performance Series Indicator/Controller Techni
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern