Rice-lake 880 Performance Series Indicator/Controller Techni Bedienungsanleitung Seite 14
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8 880 Technical/Service Manual
8. Press
MENU
to return to weighing mode.
Note
Some indicator configurations may not allow setpoints to be turned off through the front panel or may require
a password to turn the setpoint on and off.
1.4.11 Set Time and Date
1. Press
MENU
, AUDIT is displayed.
2. Press
or until T&D is displayed.
3. Press
, TIME is displayed.
4. Press
, to enter time.
5. To edit the value:
• Press
or to select the digit.
• Press
or to increment or decrement the value.
6. Press
TAR E
when the value is correct. DATE is displayed.
7. Press
, to enter date.
8. To edit the value in specified format (MMDDYY, DDMMYY, or YYMMDD):
• Press
or to select the digit.
• Press
or to increment or decrement the value.
9. Press
TAR E
when the value is correct. TIME is displayed.
10. Press
MENU
to return to weighing mode.
1.4.12 Display Accumulator
The accumulator must be enabled before use in either normal mode or setpoint operations. Once enabled, weight
(net weight if a tare is in the system) is accumulated whenever a print operation is performed using the
PRINT key,
digital input, setpoint PSHACC operation or KPRINT serial command. The scale must return to below the
threshold value (except for the setpoint PSHACC operation) before the next accumulation.
1. Press
MENU
to enter the user setup mode, AUDIT is displayed.
2. Press
or until ACCUM is displayed.
Note
Note
ACCUM is only displayed if the accumulator is enabled.
3. Press , VIEW is displayed.
4. Press
to view the current accumulator value.
5. While the accumulator value is displayed, press
PRINT
to print the value.
The format of the print output can be configured using accumulator print format. See Section 7.0.
1.4.13 Clear the Accumulator
1. Press
MENU
to enter the user setup mode, AUDIT is displayed.
2. Press
or until ACCUM is displayed.
3. Press
, then press or until CLR Y is displayed.
4. Press
TAR E
to clear the accumulator, CLEAR will display briefly and display returns to CLR Y .
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Verwandte Produkte und Handbücher für Waage Rice-lake 880 Performance Series Indicator/Controller Techni
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern