Rice-lake 880 Performance Series Indicator/Controller Techni Bedienungsanleitung Seite 32
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
26 880 Technical/Service Manual
3.0 Configuration
To configure the 880 indicator, the indicator must be placed in setup mode. The setup switch is accessed through a
small hole on the enclosure backplate, insert a non-conductive tool into the access hole and press the configuration
switch. Indicator display changes to show
SCALE.
Note
Important
Use caution when inserting the non-conductive tool into the backplate, press the tool in about 3/4 inch,
using the board as a guide, until the switch
is engaged. Do not use excessive force that may damage the
switch.
If the audit trail is enabled, setup mode may be accessed by pressing
MENU
. Press or until SETUP is
displayed, then press
to SCALE. See Section 2.9.
.
J1 J2 J3 J4 J5 J6
Setup Switch Access
Figure 3-1. Back View – Setup Switch Access
When the indicator is placed in setup mode, the word SCALE is shown on the display. The SCALE menu is the first
of eight top-level menus used for configuring the indicator. Detailed descriptions of these menus are given in
Section 3.2.
When configuration is complete, press
MENU
to return to the weigh mode.
3.1 Configuration Methods
The 880 indicator can be configured by using the front panel keys to navigate through a series of configuration
menus or by sending commands or configuration data to any communication port. Configuration using the menus
is described in Section 3.1.3.
Configuration using the communication port can be accompli
shed using either the EDP command set described in
Section 6.0 or Version 3.0 or later of the Revolut
ion configuration utility.
3.1.1 Revolution Configuration
The Revolution configuration utility provides the preferred method for configuring the 880 indicator. Revolution
runs on a personal computer to set configuration parameters for the indicator (see Section 5.0). When Revolution
configuration is complete, configuration data is downloaded to the indicator
.
3.1.2 EDP Command Configuration
The EDP command set can be used to configure the 880 indicator using either a personal computer or terminal.
Like Revolution, EDP command configuration sends commands to the indicator remote EDP port; unlike
Revolution, EDP commands can be sent using any external device capable of sending ASCII characters over a
serial connection.
EDP commands duplicate the functions availab
le using the indicator front panel and provide some functions not
otherwise available. EDP commands can be used to simulate pressing front panel keys, to configure the indicator,
or to dump lists of parameter settings. See Section 6.0 for more information about using the EDP command set.
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Verwandte Produkte und Handbücher für Waage Rice-lake 880 Performance Series Indicator/Controller Techni
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern