Rice-lake 880 Performance Series Indicator/Controller Techni Bedienungsanleitung Seite 101
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix 95
10.2 Using the HARDWARE Command
The HARDWARE serial command can be used to verify that installed option cards are recognized by the system.
The HARDWARE command returns a three-digit card code, representing the card installed:
Table 10-2. HARDWARE Command Option Card Type Codes
Code Card Type
000 No card installed
085 Relay Card
153 Analog Output Card
170 CompactCom Card
If an installed card is not recognized (HARDWARE command returns code of 0), ensure that the card is seated
properly. Reinstall the card, if necessary, then cycle the power to read the configuration again. If the card is still not
recognized, try a different option card.
10.3 ERROR Commands Output
The XE and XEH commands return a representation of any existing error conditions as described in the following
table. If more than one error condition exists, the number returned is the sum of the values representing the error
conditions. The XE command returns the value as a decimal representation and the XEH command returns the
value as a hexadecimal representation.
Table 10-3. Error Commands Output
XE Error Code
(decimal)
Description
XEH Error Code
(hexadecimal)
0 no errors 0x00000000
1 VIRGERR 0x00000001
2 PARMCHKERR 0x00000002
4 LOADCHKERR 0x00000004
8 PRINTCHKERR 0x00000008
16 ENVRAMERR 0x00000010
32 ENVCRCERR 0x00000020
64 BATTERYERR 0x00000040
32768 GRAVERR 0x00008000
65536 ADPHYSICALERR 0x00010000
131072 TAREERR 0x00020000
262144 EACCOVER 0x00040000
524288 STRINGERR 0x00080000
1048576 RESERVED_PF 0x00100000
2097152 RTCERR 0x00200000
4194304 MISSINGHWERR 0x00400000
8388608 CFGCONFLICTERR 0x00800000
16777216 UNRECOVERABLEERR 0x01000000
- 880 Performance Series 1
- Technical/Service 1
- Contents 3
- About This Manual 7
- 1.0 Introduction 7
- General Safety 8
- 1.2 Operating Modes 9
- 1.3 Front Panel Display 9
- Center of Zero LED 10
- Standstill LED 10
- 1.4 Indicator Operations 11
- 1.4.7 Print Ticket 12
- 1.4.8 Front Panel Setup 12
- 1.4.10 Setpoints 13
- Turn Setpoint On or Off 13
- 1.4.11 Set Time and Date 14
- 1.4.12 Display Accumulator 14
- 1.4.13 Clear the Accumulator 14
- 1.4.14 Display Tare 15
- 2.0 Installation 16
- 2.2 Panel Mount Installation 17
- Important 18
- J1 J2 J3 J4 J5 J6 19
- 2.4 Display Board Replacement 22
- 2.5 Cable Connections 22
- 2.6 USB Host 24
- 2.7 Ethernet Communications 24
- 2.8 CPU Board 25
- 2.10 Board Replacement 26
- 2.11 Digital I/O 28
- 2.12 Legal for Trade Sealing 28
- 2.13 Option Cards 29
- 2.14 Battery Replacement 29
- 2.15 Replacement Parts 30
- 3.1.3 User Setup Menu 33
- 0 0 0 0 0 0 34
- 3.2.1 Audit Menu 35
- 3.2.2 Setup Menu 36
- 37
- SCALE Menu 38
- 3.2.4 FORMAT Menu 40
- FORMAT Menu 41
- 3.2.5 Calibration Menu 42
- FEATUR Menu 44
- COM Menu 50
- ETHERNET Menu 52
- 3.2.11 USB Host 53
- 3.2.12 Print Format Menu 54
- Configuration 51 57
- SETPTS Menu 58
- 4.0 Calibration 63
- 4.1 Front Panel Calibration 64
- 4.1.2 Rezero 65
- 4.5 Gravity Compensation 66
- 4.6 EDP Command Calibration 67
- 4.7 Revolution 67
- Calibration 67
- 5.0 Using Revolution 68
- 5.2 Configuration 69
- 5.4 Revolution Help 70
- 6.0 EDP Commands 71
- 6.1.2 Reporting Commands 72
- Scales Menu 73
- Format Menu 73
- Calibration Menu 74
- Ports COM Menu 74
- Ports – Field Bus Menu 75
- Ports – Ethernet Menu 75
- Ports – USBCOM Menu 76
- Stream Tokens Menu 76
- Feature Menu 76
- Regulatory Menu 77
- Time and Date 77
- Passwords Menu 77
- Keypad Lock Menu 77
- Setpoints Menu 78
- Print Format Menu 80
- Analog Out Menu 80
- 6.1.5 Normal Mode Commands 81
- Digital I/O Control Menu 82
- 6.1.6 ERROR Commands Output 82
- 7.0 Print Formatting 83
- 7.2 Default Print Formats 84
- 7.3 Customizing Print Formats 85
- 7.3.3 Using Revolution 86
- 8.0 Setpoints 87
- 8.2 Batch Operations 89
- 8.3 Batching Examples 91
- Example 2 92
- 9.0 Ethernet and USB 93
- Ethernet and USB 89 95
- Using Revolution 96
- with Ethernet 96
- 9.2 USB Host 97
- 9.2.2 USB Memory storage 98
- Saving Configuration 98
- Loading Configuration 98
- 10.0 Appendix 100
- 10.3 ERROR Commands Output 101
- 10.4 Status Messages 102
- 10.6 Data Formats 103
- <STX> 104
- ONTROL-B>AXG#1<CR> 105
- 10.8.1 Toledo 8142 Indicator 108
- 10.8.2 Cardinal 738 Indicator 109
- 10.9 ASCII Character Chart 111
- 10.10 Digital Filtering 113
- (Section 4.0) 114
- 10.12 Specifications 115
- 880 Limited Warranty 116
- For More Information 117
- PN 158387 Rev C 120
Verwandte Produkte und Handbücher für Waage Rice-lake 880 Performance Series Indicator/Controller Techni
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern