Rice-lake DWM-IV Weighmeter Series 9 Setup Manual Bedienungsanleitung Seite 1

Series 9 Setup Manual

8 q Programming Recall Tare Values (Optional Series 9, if enabled) (1) The optional Series 9 can maintain up to 10 predefined Tare values. (2) To pro

9 Configuration Mode Key Functions Zero - Terminates the setup mode or exits numeric entry without changing the last value Tare - Not in use.

10 Setup/Configuration Mode Access There are two ways to access the Setup/Configuration Mode: 1) Using the Calibration Jumper (JP1) i) Turn off th

11 Configuration/Calibration Menu Choices v C1 Misc. Ø C1.1 [DPM] Display Mode Ø C1.2 [HKY] Hot-key Ø C1.3 [ATS] Auto Power Off Time Ø

12 q Default settings are highlighted. Category Selection Values Description C1 Firmware Function Settings DPM Display Mode WET Normal Weighing Mo

13 Configuration Step Values Set Description R Enable Recall Tare (Optional) RP Enable Recall Tare and Pushbutton Tare (Optional) RN Enable Recall Tar

14 Configuration Step Values Set Description C3.5 RP Remote Printer – Available on channel 1 only. This setting will behave as a Main Operation Unit

15 Configuration Step Values Set Description Print Response Retry Time-out for the bi-directional Remote Printer Communication TMO This choice is only

16 Configuration Step Values Set Description C6 Calibration REF Calibration Mode RC Standard Calibration (Zero Calibration and Span Calibration) RS

17 Calibration Audit Trail The audit trail consists of two event counters, one for the adjustment (calibration) parameters (audit trail 1) and one fo

Safety Notice ...1 Specifications...

18 Input/Output Connections Pin-Out Reference Table of HD1 HD1 is a 10-Pin Single Inline Header providing a Zero and 2-Set Point Out

19 Pin-Out Reference Table of HD2 HD2 is a 5-Pin Single Inline Header used for RS232-C Communication Pin No. 1 TxD (Transmit Data RS-232C Com

20 Jumpers, Headers and Terminal Blocks Location

21 Error Messages Error Messages Explanation CAP OL Over Capacity, weight value exceeds the full scale capacity ADC UL Input load cell signal is

22 Customizing Print Format (Optional) Ø Press [G/N] key and [Select/Enter] key together, Audit Trail will be displayed, when released the display wi

23 Ø Delay Command (DX) Delay after print which is normally placed after CR/LF, where X = Delay Time (1 = 0.1 sec). q Example: W1.8U = Print th

24 Print Output Formats & Printout Samples q Single Line Print Output Format (C3.6 = SIN) Gross^XXXXXXXX^kg^^^^^Tare^XXXXXXXX^kg^^^^^Net^XXXXX

25 Journal Print Format & Printout Sample Journal Print Format is enabled by the settings: 1) Custom Print Format Type (C3.6 “PFM” = CPR) with

26 Ø Date Format Commands (HX) Where X = Date Format No. 1 to 13 as fol lows: q Custom Journal Print Format Sample (C3.6 = CPR)

27 Journal Print Format Key Operation Following procedures are only available when the Custom Print Format contains the specific Journal Print For

1 Safety Notice It is important that FlexWeigh’s equipment is installed and operated in such a way that all applicable safety requirements are met.

28 How to print the Grand Total: After the last batch Sub Total Data Print, issue the Grand Total Data Print as foll ows: 1) Press [Shift] then press

29 How to setup the current Date and Time: The following are the sequence of date and time setups, just after the display count down finished: After

30 Setup Record Table Owner Ø Scale Model Ø Firmware Version Ø Serial Number Ø Date of Purchase Ø Capacity & Division Ø Setup Date

31 Display Character Reference 0 1 2 3 4 5 6 7 8 9 A B C E D F G

32 ASCII Character Set

33 Password The calibration/configuration password is: 2001

2 Specifications Internal Resolution 1,000,000 counts at 3mV/V Display Resolution Selectable (1/10,000 NTEP approval pending) Input Sensitivity 1

3 Series 9 (Group ‘A’ Keys) Front Panel rieys) Front Panel Group ‘A’ Keys Gr

4 Status Indicators There are 7 LED indicators just below the 7-segment weight display with the following functions. S

5 Key Functions Group ‘A’ ON / OFF – Power switch used to switch on and off the Series 9 meter. ZERO – Zero button used to zero the indica

6 Optional Key Functions Group ‘B’ ‘0’ / F10 - Enters ‘0’, space, Double Quotation Mark or Back Slash depending upon the current mode of operation.

7 Operating Instructions q Power ON Zeroing Upon applying power the instrument will: i) If the applied load is less than or equal to 2% of the cali